Subaru forester 2022 garage door opener setup

In an age where technology is mainstream, anything that can make your day simpler is paramount. Everyone has a busy schedule these days and that doesn't just pertain to the work day. Things as simple as an automatic garage door opener can simplify your day and make your life easier. Your garage door opener won't function properly though if its not programmed to work with your garage. This happens to be a very simple task.

Table of Contents Show

Gate Operator/Canadian Programming
Other information:
Subaru Forester 2019-2022 Owners Manual: Climate Control settings
Subaru Forester 2019-2022 Owners Manual: Operation
How do I program my garage door opener in my Subaru without a remote?
Does Forester have HomeLink?

Park your Subaru Forester in front of your garage.

Press and hold your garage door opener button while simultaneously pressing one of the three homelink buttons on your rear-view mirror.

The button will start blinking. Keep holding the button until the blinking changes. Your Subaru Forester garage door opener has now learned the code to open your garage.

Indicator Light
HomeLink Buttons

Press and release the HomeLink button that you would like to program. The HomeLink indicator light will flash orange slowly (if not, refer to “Erasing HomeLink Buttons”).
Garage door opener remote
Position the hand-held remote (garage door opener remote) 1 to 3 inches (2 to 8 cm) away from the HomeLink button that you would like to program.
NOTE
Some hand-held remotes (garage door opener remotes) may actually train better at a distance of 6 to 12 inches (15 to 30 cm). Keep this in mind if you have difficulty with the programming process.
While the HomeLink indicator light is flashing orange, press and hold the handheld remote button. Continue pressing the hand-held remote button until the HomeLink indicator light changes from orange to green. You may now release the hand-held remote button.
NOTE
Some devices may require you to replace this “Programming a New HomeLink Button” step 3 with procedures noted in the “Gate Operator / Canadian Programming” section. Refer to “Gate Operator/Canadian Programming”.
Indicator Light
Press the HomeLink button that you would like to program and observe the indicator light.
- If the indicator light remains constant green, your device should operate when the HomeLink button is pressed. At this point, if your device operates, programming is complete.
- If the indicator light rapidly flashes green, firmly press, hold for two seconds and release the HomeLink button up to three times to complete the programming process. At this point if your device operates, programming is complete. If the device does not operate, continue with the next step of the programming instructions.
“Learn” button
At the garage door opener motor, (security gate motor, etc.) locate the “Learn”, “Smart”, or “Program” button. This can usually be found where the hanging antenna wire is attached to the motor-head unit (see the device’s manual to identify this button). The name and color of the button may vary by manufacturer.
NOTE
A ladder and/or second person may simplify the following steps.
Firmly press and release the “Learn”, “Smart”, or “Program” button. You now have 30 seconds in which to complete step
Return to the vehicle and firmly press, hold for two seconds and release the HomeLink button up to three times. At this point programming is complete and your device should operate when the HomeLink button is pressed and released.

Status Indicators
If status indicator arrows appear next to the indicator light, please refer to “Garage Door Two-Way Communication”

In the event that there are still programming difficulties or questions, additional HomeLink information and programming videos can be found at www.HomeLink.com and www.youtube.com/HomeLinkGentex. For Genie and Sommer garage door openers please go directly to the HomeLink website.

Gate Operator/Canadian Programming

Canadian radio-frequency laws require transmitter remote signals to “time-out” (or quit) after several seconds of transmission, which may not be long enough for HomeLink to pick up the signal during programming...

Other information:

Subaru Forester 2019-2022 Owners Manual: Climate Control settings

You can set the climate control settings. Mode Setting Select “Mode Setting” from the 2nd menu in the setting screen. Refer to “Setting screen”. Select “Normal”, “Mild”, “Power” or “ECO” by using the control switches. For details about “Mode Setting”, refer to “Automatic climate control customization (for type B and C)”...

Subaru Forester 2019-2022 Owners Manual: Operation

Driver’s side Passenger’s side SRS AIRBAGs deploy as soon as a collision occurs. After deployment, SRS AIRBAGs start to deflate immediately so that the driver’s vision is not obstructed. The SRS airbags can function only when the ignition switch is in the “ON” position...

How do I program my garage door opener in my Subaru without a remote?

Go to the control box inside your garage and look for a button marked 'learn', 'program', or 'smart'. Press that button then go back to the car. You have about 30 seconds to finish this step or you'll have to start from scratch. Now get back in the car and press the replacement button you've just programmed.

Does Forester have HomeLink?

Subaru Forester: Mirrors / Programming a New HomeLink Button. Press and release the HomeLink button that you would like to program. The HomeLink indicator light will flash orange slowly (if not, refer to “Erasing HomeLink Buttons”).

subaru forester garage door opener setup