Kenmore coldspot model 106 water filter location

If you have a refrigerator with a water dispenser, you can be pretty sure it has a filter built in. You probably know you should replace the filter at some point, but like many people, you may wonder why you should bother replacing it, how often you should replace it and how to remove the filter. There's no reason to put off replacing a water filter when the process is so simple.

How to Locate a Refrigerator Water Filter

Image Credit: Caiaimage/Paul Bradbury/Caiaimage/GettyImages

Video of the Day

When to Replace Your Filter

Refrigerator water filters should be replaced every six months, when the filter notification light turns on or when the water starts to taste or smell noticeably different. The change in smell and odor occurs because the filter is full of contaminants and can no longer work effectively, leaving you with water that's essentially the same as tap water. Neglecting to change your filter for too long will not only leave you with inferior tasting water, but the mineral deposits from the unfiltered water could even damage your refrigerator's water system.

Advertisement

In some areas, the water filter may be exhausted in far less time than six months; however, it may work much longer than six months in locations with notably clean tap water. Even so, six months is an easy-to-remember time frame for changing the filter, especially since you might not notice a change in the water's taste if it occurs gradually over the course of six months or more.

Finding Your Filter

Most water filters are located in the grille at the bottom of the refrigerator or the back, upper-right corner of the inside of the refrigerator. Some models, usually older ones, have the filter on the outside in the back of the refrigerator on the water supply line.

Advertisement

The best way to find your filter is to look at the inside corner of your refrigerator and at the grille at the bottom. The filter will look like a round tube, about 3 to 4 inches wide. If you don't see the filter in one of these two areas, you might want to check your owner's manual or look up the model number online to find out the exact location before pulling the unit away from the wall to look at the back of the refrigerator.

Advertisement

Replacing the Water Filter

If the removal process for your specific water filter doesn't seem immediately obvious, you may want to consult your user manual or look your model number up online to find out how to remove the filter. That being said, there are three general removal methods for taking out a water filter: push in, twist in and inline:

Advertisement

• Push-in filters can be removed by pushing the "eject" button or twisting off the filter cap. To install the new filter, line up the arrows, snap it into place by turning the filter clockwise and then push it in until the eject button pops.
  
• Twist-in filters can be replaced by twisting the old cartridge out, removing the cap, putting the cap on the new filter and twisting the new unit in.
  
• Inline filters are those found on the back of the refrigerator, hooked up to the incoming water supply line. Some units will be easy to remove and simply twist out like the twist-in filters, while others are more difficult to replace as they require cutting a portion of the tubing. As a result, you may want to work with a professional to replace these filters.
  

Advertisement

Whatever type of filter you have, it's a good idea to write down the make and model number from your old filter before throwing it away so you can get the right replacement if you haven't already bought one.

After replacing the filter, run a gallon of water through the unit to clear carbon residue from the filter. Once that's done, your filter is ready to go.

By jojo | 15 November 2014 | 0 Comments

Replacing Kenmore Water Filters

46-9085, 46-9902, 46-9908, 46-9010 Ice & Water Refrigerator Filter 5 4396508 EDR5RXD1
1/4 Turn Filter Thru Lower Front Grill
Installation Instructions
Locate Filter at bottom grille and Twist the old filter a quarter-turn counterclockwise.
Pull the filter straight out (the water will shut off automatically).
Remove the reusable color-keyed cap from the end.
Discard the old filter.
Slide the cap onto the end of the new filter.
Push the new filter into the fridge until it stops.
Twist the filter a quarter-turn clockwise.
Flush 1 - 2 Gallons of Water to Purge Out Air From System.
That's how easy it is to replace the 4396508 water filter.
Reset your 'change filter' light (if your fridge has one).
PRODUCT PAGE

46-9086, 46-9915 Ice & 1/4 Turn Filter Thru Lower Front Grill (FREEZER ON TOP MODELS)
Installation Instructions
Locate Filter at bottom grille and Twist the old filter a quarter-turn counterclockwise.
Pull the filter straight out (the water will shut off automatically).
Remove the reusable color-keyed cap from the end.
Discard the old filter.
Slide the cap onto the end of the new filter.
Push the new filter into the fridge until it stops.
Twist the filter a quarter-turn clockwise.
Flush 1 - 2 Gallons of Water to Purge Out Air From System.
That's how easy it is to replace the 4396701 water filter.
Reset your 'change filter' light (if your fridge has one).
PRODUCT PAGE

46-9083, 46-9020, 46-9030 Ice & Water Refrigerator Filter 3 4396841 EDR3RXD1
Large Push Button Filter Thru Lower Front Grill
Installation Instructions
Locate Filter at bottom grille and Press the button to the left of the filter to release it.
Pull the filter straight out (the water will shut off automatically).
Remove the reusable color-keyed cap from the end.
Discard the old filter.
Twist the cap onto the end of the new filter.
Push the new filter straight in until it 'Clicks' into place.
Note: To install filter push until you hear the receiver click into place. Improper installation may cause leaks, damage to flooring and appliances.
Flush 1 - 2 Gallons of Water to Purge Out Air From System.
That's how easy it is to replace the 4396841 water filter.
Reset your 'change filter' light (if your fridge has one).
PRODUCT PAGE

46-9084, 46-9006, 46-9992 Ice & Water Filter PuriCleanII UKF8001 EDR4RXD1
Inside At The Ceiling In A Flip Down Tray
Installation Instructions
Locate the filter in a flip down compartment at the upper right ceiling of the refrigerator and Unlatch the plastic filter cover. Let it swing down (so you can see the filter).
While pushing in, Twist the old filter counterclockwise until it is free.
Slide the filter straight out and discard (the water will shut off automatically).
Push the new filter into the fridge and Twist clockwise until it is fully in place.
Push the plastic filter cover up until it snaps closed.
Flush 1 - 2 Gallons of Water to Purge Out Air From System.
That's how easy it is to replace the UKF8001 water filter.
Reset your 'change filter' light (if your fridge has one).
PRODUCT PAGE

46-9002 Refrigerator Water Filter 8 EDR8D1 8171413
Located Inside the Fridge at the Upper Right
Installation Instructions
Twist the old filter a quarter-turn counterclockwise.
Pull the filter straight down and discard (the water will shut off automatically).
Push the new filter up into the fridge until it stops.
Twist the filter a quarter-turn clockwise.
Flush 1 - 2 Gallons of Water to Purge Out Air From System.
That's how easy it is to replace the 8171413 water filter.
Reset your 'change filter' light (if your fridge has one).
PRODUCT PAGE

46-9081, 46-9930 Ice & Water Refrigerator Filter 1 W10295370A EDR1RXD1
Two Locations
(1) Located Inside the Fridge at the Upper Right
Installation Instructions
Locate filter compartment at the right upper corner inside the refrigerator.
You might have to remove the upper shelf for more room.
Gently lift up on filter cover and filter will automatically slide out.
Slide old filter all the way out, noticing the arrow on the end is facing up. (the water will shut off automatically).
Discard the old filter.
Line the arrow on end of the new filter upward.
Gently Push the new filter into the fridge with arrow facing up till it stops.
As you close the filter cover you will notice that the filter will go in and lock into place.
Reinstall Shelf (if taken out).
Flush 1 - 2 Gallons of Water to Purge Out Air From System.
That's how easy it is to replace the EDR1RXD1 water filter.
Reset your 'change filter' light (if your fridge has one).
PRODUCT PAGE

(2) Located Thru Lower Front Grill
Installation Instructions
Locate filter at the lower front grill of refrigerator.
Gently lift up on filter cover and filter will automatically slide out.
Slide old filter all the way out, noticing the arrow on the end is facing up. (the water will shut off automatically)
Discard the old filter.
Line the arrow on end of the new filter upward & Gently Push the new filter into the fridge with arrow facing up till it stops.
As you close the filter cover you will notice that the filter will go in and lock into place.
Flush 1 - 2 Gallons of Water to Purge Out Air From System.
That's how easy it is to replace the EDR1RXD1 water filter.
Reset your 'change filter' light (if your fridge has one).
PRODUCT PAGE

46-9082, 46-9903 Ice & Water Refrigerator Filter 2 W10413645A EDR2RXD1
Located Inside the Fridge at the Upper Right
Installation Instructions
Locate filter compartment at the top inside the refrigerator.
You might have to remove the upper shelf for more room.
Push on the filter cover to open filter compartment.
The filter will drop down and to remove you will push in and turn counterclockwise until it is out. (the water will shut off automatically).
Discard the old filter.
Line the knotch on end of the new filter upward.
Push the new filter into the fridge with knotch facing up and push filter while twisting clockwise till it locks into place.
Push filter upward till it locks in the compartment and close the cover.
Re-install Shelf (if taken out).
Flush 1 - 2 Gallons of Water to Purge Out Air From System.
That's how easy it is to replace the EDR2RXD1 water filter.
Reset your 'change filter' light (if your fridge has one).
PRODUCT PAGE

Kenmore (253. Series) has three locations for their refrigerator water filters. They are
'Interior Upper Right Rear Corner Inside a Filter Cup'
'Interior Upper Right Front'
'Interior Upper Right Rear Corner'
See below to learn how to remove and replace your Kenmore water filter yourself.

46-9916, 46-9911 Cassette Style Water Filter PureSource2 WF2CB
Inside at the Upper Front
Installation Instructions
Locate Filter inside fridge at upper front, Press the button to the right of the filter to release it.
Pull the old filter straight out and discard (the water will shut off automatically).
Push the new filter in VERY FIRMLY until you hear it 'CLICK' into place.
Flush 1 - 2 Gallons of Water to Purge Out Air From System.
That's how easy it is to replace the PureSource2 water filter.
Reset your 'change filter' light (if your fridge has one).
PRODUCT PAGE

46-9906, 46-9910 Water Filter PureSourcePlus WFCB
Inside at the Upper Right Rear Corner Inside a Filter Cup
Installation Instructions
Locate Filter Cup inside fridge at right upper rear wall.
Remove upper shelf for more room if needed.
Unscrew the filter cup and dump out the water.
Pull the old filter straight down and discard.
Place the new filter in the filter cup.
The end of the filter with the small o-ring should be up.
Screw the filter cup (with filter) up onto the housing.
The filter should self-align as the cup is tightened.
Replace shelf (if removed).
Flush 1 - 2 Gallons of Water to Purge Out Air From System.
That's how easy it is to replace the PureSource Plus water filter.
Reset your 'change filter' light (if your fridge has one).
PRODUCT PAGE

46-9906, 46-9910 Water Filter PureSource WF1CB
Inside at the Upper Right Rear Corner Inside a Filter Cup
Installation Instructions
Locate Filter Cup inside fridge at right upper rear wall.
Remove upper shelf for more room if needed.
Unscrew the filter cup and dump out the water.
Pull the old filter straight down and discard.
Place the new filter in the filter cup.
The end of the filter with the small o-ring should be up.
Screw the filter cup (with filter) up onto the housing.
The filter should self-align as the cup is tightened.
Replace shelf (if removed).
Flush 1 - 2 Gallons of Water to Purge Out Air From System.
That's how easy it is to replace the PureSource water filter.
Reset your 'change filter' light (if your fridge has one).
PRODUCT PAGE

46-9999 Ultra Water Filter ULTRAWF
Inside at the Upper Right Rear Corner
Installation Instructions
Remove the old filter by pushing (and letting go) on the end (Face) of the filter.
Slide out the old filter and insert the new filter and push firmly till the new filter snaps into place.
When you hear it click (It is locked into place).
Flush 1 - 2 Gallons of Water to Purge Out Air From System.
That's how easy it is to replace the ULTRA water filter.
Reset your 'change filter' light (if your fridge has one).
PRODUCT PAGE

Kenmore (363. Series) has two locations for their refrigerator water filters. Find either
'Interior Upper Right Rear Corner'
'Interior At The Ceiling In A Flip Down Tray'
See below to learn how to remove and replace your Kenmore water filter yourself.

46-9905 SmartWater Water Filter MWF MWFP
Inside at the Upper Right Rear Corner
Installation Instructions
Locate Filter inside fridge and turn it 1/2 turn counterclockwise.
Pull the old filter straight down and discard (the water will shut off automatically).
Push the new filter gently up and in until it stops.
Turn the filter clockwise until it stops.
Flush 1 - 2 Gallons of Water to Purge Out Air From System.
That's how easy it is to replace the MWFP water filter.
Reset your 'change filter' light (if your fridge has one).
PRODUCT PAGE

46-9914 SmartWater Water Filter GSWF
Inside At The Ceiling In A Flip Down Tray
Installation Instructions
Locate Filter inside fridge at the ceiling.
Unlatch the plastic filter cover, and let it swing down to see the filter.
Twist the old filter a quarter-turn counterclockwise and discard (the water will shut off automatically).
Push the new filter in until it stops and Twist the filter a quarter-turn clockwise.
Swing the plastic filter cover up until it snaps closed.
Flush 1 - 2 Gallons of Water to Purge Out Air From System.
That's how easy it is to replace the GSWF water filter.
Reset your 'change filter' light (if your fridge has one).
PRODUCT PAGE

Kenmore (596. Series) has two locations for their refrigerator water filters. Find either
'Interior Upper Right Rear Corner'
'Interior At The Ceiling In A Flip Down Tray'
See below to learn how to remove and replace your Amana water filter yourself.

46-9904 Clean 'n Clear Water Filter WF401 12527304
Inside at the Upper Right Rear Corner
Installation Instructions
Locate the filter inside the refrigerator at the right rear in a vertical posititon.
Twist the old filter counterclockwise until it is free.
Remove the filter straight down and discard (the water will shut off automatically).
Push the new filter into the fridge and Twist clockwise until it is fully in place.
Flush 1 - 2 Gallons of Water to Purge Out Air From System.
That's how easy it is to replace the WF401 water filter.
Reset your 'change filter' light (if your fridge has one).
PRODUCT PAGE

46-9084, 46-9006, 46-9992 PuriCleanII Water Filter UKF8001 EDR4RXD1
Inside At The Ceiling In A Flip Down Tray
Installation Instructions
Locate the filter in a flip down compartment at the upper right ceiling of the refrigerator and Unlatch the plastic filter cover. Let it swing down (so you can see the filter).
While pushing in, Twist the old filter counterclockwise until it is free.
Slide the filter straight out and discard (the water will shut off automatically).
Push the new filter into the fridge and Twist clockwise until it is fully in place.
Push the plastic filter cover up until it snaps closed.
Flush 1 - 2 Gallons of Water to Purge Out Air From System.
That's how easy it is to replace the UKF8001 water filter.
Reset your 'change filter' light (if your fridge has one).
PRODUCT PAGE

Kenmore (596. Series) has three locations for their refrigerator water filters. Find either
'Interior Upper Right Rear Corner'
'Interior Horizontally at Ceiling'
'Interior At The Ceiling In A Flip Down Tray'
See below to learn how to remove and replace your LG water filter yourself.

46-9890 5231JA2002A WATER FILTER LT500P
Inside at the Upper Right Rear Corner
Installation Instructions
Locate the existing filter. It will be located behind the light cover above the top shelf on the right hand side.
Remove the top shelf. This will give you more room to remove and install the new filter.
Remove the light cover by pressing the release clip on the bottom of the cover and pulling the cover out and up to remove the light cover.
Locate existing filter and remove it by turning it counter clockwise.
Holding new filter in your hands, carefully remove the packaging and sanitary end-cap from the new filter. Check the black o-rings making sure they are both on and not damaged (torn or cracked).
Locate the Start arrow found at the top of the instruction label on the back side of the filter and Align the Start arrow with the arrow on the refrigerator filter head.
Apply slight upward pressure and rotate the filter clockwise until the Stop arrow on the front of the filter label is aligned with the arrow on the refrigerator filter head.
Ensure filter is fully installed in the refrigerator filter head a full 1/4 turn. This is required to activate the internal valve inside the refrigerator. If the filter is not turned 1/4 turn the valve will not fully open and may cause the water flow to be slow, or even cause the valve to make a chattering noise during use.
Replace the light cover and top shelf.
Dispense water for approx. 2 gallons making sure that air and water is completely flushed from the system.
That's how easy it is to replace the 5231JA2002A LT500P WATER FILTER.
Reset your 'change filter' light (if your fridge has one).
PRODUCT PAGE

46-9990 5231JA2006 WATER FILTER LT600P
Inside Horizontally at Ceiling
Installation Instructions
Locate existing filter and remove it by turning it counter clockwise. The filter will eject slightly with a clicking sound. Discard old filter.
Holding new filter in your hands, carefully remove the packaging and sanitary end-cap from the new filter.
Insert the new filter into the refrigerator filter receptacle. With the handle in the vertical position, push the new filter into the housing until it stops. When inserting the new filter, twist the handle slightly left to right, while pushing inward.
Rotate the filter clockwise a full 1/4 turn until you feel it stop. Ensure filter is fully installed in refrigerator head a full 1/4 turn. This is required to activate the internal valve inside the refrigerator.
If the filter is not turned a full 1/4 turn the valve will not fully open and may cause the water flow to be slow, or even cause the valve to make a chattering noise during use.
Run water from the dispenser for 5 minutes - (about 2½ gallons) to clear the system and prevent sputtering.
That's how easy it is to replace the 5231JA2006 LT600P water filter.
Reset your 'change filter' light (if your fridge has one).
PRODUCT PAGE

46-9690 ADQ36006101 WATER FILTER LT700P
Inside At The Ceiling In A Flip Down Tray
Installation Instructions
Locate Filter and Push button to open filter cover.
Pull cartridge down & Pull out the filter. NOTE: If the filter is hard to remove, turn off water supply and relieve pressure at refrigerator door water dispenser before installing new filter.
Holding new filter, remove the packaging and end-cap.
Insert the new filter into the manifold hole until it stops.
Push the cover back up until it clicks into place.
Run water from the dispenser for 5 minutes (about 2½ gallons) to clear the system and prevent sputtering.
That's how easy it is to replace the ADQ36006101 LT700P water filter.
Reset your 'change filter' light (if your fridge has one).
PRODUCT PAGE
 

Leave a Reply

Your email address will not be published.Required fields are marked. *

How do I know if my Kenmore refrigerator has a water filter?